Jocelyn's preventer line led forward along the side deck

Boat-specific ideas from aboard Jocelyn

Single-Handing a Jeanneau Sun Odyssey 350

The arrangements, equipment choices and working habits that help me sail and manage my Jeanneau Sun Odyssey 350 alone.

A growing working notebook

What works for me aboard Jocelyn

This is not a general guide to sailing single-handed. It is a growing collection of practical ideas I have adopted, adapted or learned while sailing and managing Jocelyn, my Jeanneau Sun Odyssey 350, alone. Some may also suit other Sun Odyssey models, but each begins with this particular boat, her layout and the way I use her.

Some arrangements solve a specific irritation; others reduce the number of times I need to leave the cockpit or help me conserve energy for the end of the day.

The archive will grow as arrangements are tested over more passages. Where something is still experimental, I will say so.

Tip 01 · Sail handling

A preventer I can control from the cockpit

Because I sail alone so often, I wanted a preventer that I could prepare at the start of the day and then rig, tension and release without going forward while under way.

This arrangement is also quite specific to Jocelyn and the Sun Odyssey 350. The boom cannot be eased as far out as it might be on a more traditional yacht. I initially tried taking a line directly from the end of the boom to the bow, but on this boat that route tended to snag and was not particularly effective. Leading one continuous line around the boat through permanently mounted friction rings has proved a much better fit for Jocelyn’s layout.

The system has two parts. A short black Dyneema pennant is secured permanently at the aft end of the boom with a Dyneema soft shackle. The working part is one long continuous line led from one helm, forward along both sides of the boat, and back to the opposite helm.

I favour soft shackles for the boom connections because there is no heavy metal fitting to strike the deck—or me—when the sail and lines are moving.

Why it suits this boat

Once the continuous line is in place, every working end remains within reach of a helm. I do not need to go forward to rig or use the preventer.

First recorded and photographed during Passage 019: A Bimble, a Race and a Pizza.

  1. 01
    Rig the continuous line

    At the start of the day, I lead the line from one aft helm through the friction ring permanently mounted at the midships cleat. It continues forward through the friction ring at the bottom of the staysail connector, then returns down the other side through the opposite midships ring and back to the other helm.

  2. 02
    Connect it once clear of the river

    When I am ready to use the preventer, I connect the line to the black Dyneema boom pennant using a soft shackle. The deck line is already routed, so this connection can be made from the cockpit area.

  3. 03
    Tension it from the opposite helm

    I tension and tie off the preventer on the side opposite the one to which the boom is eased, using the aft cleat at that helm station. The other end remains available for the next change of side.

Black Dyneema preventer pennant attached permanently at the aft end of Jocelyn's boom
The permanent black Dyneema pennant at the aft end of the boom.
White and blue preventer line led aft along Jocelyn's side deck
The continuous line returning aft along the side deck.
White and blue preventer line secured to the cleat beside Jocelyn's aft helm
The working end secured at the aft helm cleat.
Dyneema boom pennant connected to the continuous preventer line aboard Jocelyn
The boom pennant joined to the working line while sailing.

Tip 02 · Single-handed preparation

A spinnaker releaser for the main halyard

On my previous Jocelyn, I once looked up to discover that the main halyard had wrapped around the spreaders. Untangling it was difficult enough to make me determined to prevent the same thing happening again.

The blue fitting shown here is normally used as a spinnaker releaser. I use it to keep the main halyard taut and close to the mast. It holds firmly enough to stop the halyard working loose, but releases when I deliberately pull the halyard from the cockpit to hoist the mainsail.

Why it helps me

The halyard remains ready to use and I do not have to visit the mast before every hoist. For my single-handed sailing, that small adaptation has been a game changer.

Blue spinnaker releaser holding Jocelyn's main halyard close to the mast
The releaser holds the main halyard close to the mast until I pull from the cockpit.

Tip 03 · Electrical load management

Using the Bluetti to manage Jocelyn’s electrical loads

I ordered air conditioning because marinas can become ridiculously hot and uncomfortable. At my age I want some comfort, and I also wanted the option of cooling part of Jocelyn while at anchor.

The real reason for buying the Bluetti Elite 300 was to manage the electrical loads safely and practically. Jocelyn has two separate 230-volt shore-power circuits and inlets. The main circuit supplies the boat’s sockets, battery charger, hot-water system and other normal services. The second circuit is dedicated to the air conditioning.

That arrangement is straightforward where two suitably rated marina supplies are available. The practical limitation I regularly encounter in the UK is a single 16-amp outlet at the berth. I did not want to combine Jocelyn’s two shore leads through a Y-piece and potentially ask one 16-amp supply to carry loads approaching the combined demand of both circuits.

My answer is to connect Jocelyn’s normal shore-power circuit to the marina supply and use the Bluetti as a completely separate source for the air conditioning. This leaves the shore connection available for the battery charger, sockets, hot water and occasional domestic loads such as the kettle, while avoiding two boat circuits being combined into one marina outlet.

Observed endurance aboard Jocelyn

With both air-conditioning zones selected and the fans running at full speed, I have seen about two and a half hours from a charged Bluetti. This is my observed result, not a guaranteed runtime: temperature, compressor cycling, fan setting, battery state and the other loads in use will all change it.

There are two air-conditioning zones. One serves the saloon and forward cabin; the other serves the aft cabin and heads. At anchor I normally select only the aft zone and cool the cabin in which I will sleep. In my use that reduces the air-conditioning demand by roughly half and makes much better use of the stored energy.

At the marina I manage the loads in sequence. I first use the normal shore circuit to charge the boat, heat the water and make my coffee. Once those higher demands have finished, I switch them off and recharge the Bluetti from one of Jocelyn’s standard three-pin sockets while the Bluetti continues to supply the air conditioning. It still requires thought and monitoring, but it is much simpler for me than trying to run two shore leads from one outlet—and I retain the added benefit of air conditioning at anchor.

I rarely use Jocelyn’s gas cooker, so the Bluetti can also power my Tefal air fryer, kettle, toaster and portable electronics when the air conditioning is not taking priority.

I can take the Bluetti and cooking appliance into the cockpit to cook pizza, bacon, steak or whatever else I fancy in the fresh air. The fat, smoke, cooking smells and other unmentionables can dissipate outside instead of filling the cabin and settling over the interior. I keep the equipment securely positioned, ventilated and sheltered from spray or weather while it is in use.

I always keep within the ratings of the marina outlet, Jocelyn’s circuits, the Bluetti, connectors and appliances, and I follow the manufacturers’ guidance for ventilation, charging and cable routing.

  1. 01
    Use the marina supply for Jocelyn

    I connect the normal shore-power inlet so the boat can run its sockets, charger and hot-water system without combining it with the dedicated air-conditioning circuit.

  2. 02
    Keep air conditioning separate

    I connect the Bluetti to the dedicated air-conditioning system through my existing boat connections, keeping that demand separate from the single marina outlet.

  3. 03
    Sequence the heavier loads

    I charge the boat, heat the water and use the kettle first. When those jobs are finished, I switch them off before using a boat socket to recharge the Bluetti while it powers the air conditioning.

  4. 04
    Cool only the space I need

    At anchor I normally run only the aft-cabin and heads zone. I monitor the remaining energy and choose comfort in the sleeping cabin rather than trying to cool the whole boat.

Bluetti Elite 300 portable power station positioned beside Jocelyn's saloon seating
The Bluetti provides a separate, managed supply for air conditioning and selected domestic loads.
Tefal air fryer positioned on Jocelyn's cockpit table
I cook in the cockpit so fat, smoke and cooking smells can disperse outside rather than filling Jocelyn’s cabin.

Tip 04 · Navigation displays

Positioning the ORCA display where I naturally stand

Jocelyn’s Raymarine displays are at the helms, but once the boat is settled I often stand near the cockpit table, tucked behind the sprayhood. From there, the helm displays are not naturally in my sightline.

Mounting the ORCA display beside this working position has resolved that frustration. I can see the sailing instruments and navigation information without repeatedly moving back to a helm.

I keep ORCA independent from the Raymarine Axiom displays and use the systems to cross-check one another. On the same passage, ORCA briefly showed a position that was obviously wrong. A polished display is useful, but it should never replace looking outside or checking another source.

Why it helps me

The best display position is the place from which I actually sail—not simply the place where a display is conventionally fitted.

ORCA navigation display mounted beside Jocelyn's cockpit table and sprayhood
The ORCA display is visible from my usual position behind the sprayhood.

Tip 05 · Anchoring

A single-handed anchor snubber for Jocelyn

I initially had quite a problem deciding how I was going to use a snubber aboard Jocelyn. The line is important because it takes the anchoring load away from the windlass and its flexibility helps soften the snatching as the boat moves.

A conventional bridle led to both bow cleats would be the more usual arrangement, but I could not see a sensible way to rig one alone. Reaching out around the anchor roller and bowsprit is simply too far for me, especially when I am already managing the anchor single-handed.

My solution is one six-metre snubber line secured to the starboard bow cleat. The other end is joined to the chain with a suitably rated Dyneema soft shackle while the chain is still accessible inside the anchor locker. As with my preventer, I prefer the soft connection; a metal chain hook or shackle will not pass through Jocelyn’s closely designed anchor roller, whereas the Dyneema can be strong enough for the load while remaining slim enough to travel through it.

I have fitted anti-chafe protection where the snubber bears against the starboard cleat and arranged a second protected section to travel through the bow roller. The idea is to protect the line at both likely wear points—a belt-and-braces approach—but I have not yet used the arrangement enough to say how effective the bow-roller protection will be over time.

Where I use it

This arrangement has worked well so far for quiet anchorages and an overnight stop. I would not assume that it is suitable for a big rolling sea; I still need to judge the conditions, expected loads and the complete anchoring arrangement each time.

The snubber was first recorded in use with 20 metres of chain during Passage 019: A Bimble, a Race and a Pizza.

  1. 01
    Secure and protect the inboard end

    Before paying out the final chain, I make the six-metre snubber fast to Jocelyn’s starboard bow cleat, position the anti-chafe protection where the line bears on the cleat and check that everything is clear to run.

  2. 02
    Attach it inside the locker

    While the chain is still within easy reach, I connect the snubber to a chain link using a suitably rated Dyneema soft shackle. This avoids leaning out over the bow roller or bowsprit.

  3. 03
    Lead and protect the line

    I lead the rope to the left of the central bow-roller guide as seen from aboard and arrange the second anti-chafe section to pass through the roller. I check that neither the line nor its protection is trapped and that both can follow the chain cleanly.

  4. 04
    Transfer the load

    I continue easing the chain until the snubber takes the strain, leaving the chain beyond it slack enough that the working load is carried by the line rather than the windlass.

Anchor chain and snubber accessible inside Jocelyn's open anchor locker
The chain remains accessible inside the locker, allowing the soft shackle to be attached without reaching beyond the bow.
Jocelyn's chain and dark snubber line passing through the bow roller
The slim soft-shackle connection and protected snubber section pass through the restricted anchor-roller arrangement alongside the chain.
Snubber line led from Jocelyn's starboard bow cleat towards the anchor chain
The six-metre line is secured at the starboard bow cleat, with anti-chafe protection at the cleat, before being led forward.
View ahead from Jocelyn while settled in a quiet anchorage
The kind of quiet anchorage for which I currently consider this single-line arrangement appropriate.

Tip 06 · Managing the boat alone

The little fitting that transformed filling Jocelyn’s water tanks

Filling Jocelyn’s water tanks ought to be a straightforward job, but doing it alone used to be surprisingly awkward. I would push the hose as far into the deck filler as possible, walk back along the pontoon to turn on the tap and hope it remained in place. It rarely did. More often than not I had to stand holding the hose throughout—and usually ended up getting wet.

This small cap, made by a small company in Switzerland, has completely changed the job. It seats securely inside Jocelyn’s water deck filler and turns it into a proper hose connection. The hose attaches to the cap using an ordinary quick-release connector, while an inline valve places the water control immediately beside the filler instead of back at the marina tap.

Once everything is connected, the hose stays where it belongs and I can start, reduce or stop the flow without leaving the boat. I am free to move around Jocelyn and attend to nearby jobs while continuing to keep an eye on the tank, rather than spending the whole time crouched beside the filler gripping a loose hose.

Why it is such a useful single-handed solution

The cap holds the hose securely and the inline valve puts the control exactly where I need it. A frustrating job that once required me to be in two places at once is now simple, tidy and entirely manageable by one person.

I still check that every connection is secure, use a clean drinking-water hose and continue monitoring the tank so that I can stop before it overflows. The fitting does not make the process unattended; it simply gives me secure attachment and complete control from the boat.

Removable water-filling cap with hose adaptor beside Jocelyn's open deck filler
The removable cap carries the quick-release hose connector and is shaped to seat inside Jocelyn’s water deck filler.
Water-filling cap seated securely in Jocelyn's blue deck filler
The cap seated securely in the blue deck fitting, ready for the hose connection.
Water hose connected to Jocelyn's deck filler through the special cap and a nearby control valve
The complete arrangement, with the hose held securely and the inline flow-control valve within easy reach.

Small habits that make a difference

Quick tips from the passage archive

01

Free the lazy sheet before tacking

Before a single-handed tack, I check that the lazy genoa sheet is free to run. A few seconds of preparation avoids an unnecessary complication during the manoeuvre.

02

Choose visibility over a little speed

In busy Harwich water I rolled away the genoa to improve my view. I was slower, but the clearer lookout mattered more than the lost speed.

03

Keep energy for the arrival

Sailing does not finish at the harbour entrance. Berthing, lines, fenders, covers and tidying still follow, so I make sail-handling decisions with enough energy in reserve to finish safely.

04

Cross-check every navigation source

If an electronic position conflicts with the surroundings, I check the other displays, instruments and what I can see. No single system earns unquestioning trust.